Open fan coil with deposits in the condensate tray
Case study · AirBio project ashore

Fan Coils and Split Units Cleaned and Sanitized at a Diagnostic Centre

Mould on the panels, deposits in the condensate trays, dust packed between the coil fins: the same picture we find in yacht cabins.

Over three days in January 2021, AirBio opened, cleaned and sanitized the fan coils and split units of the Centro Diagnostico Castellano in Castelfranco Veneto, Italy, and documented every unit type with before and after photos.

Italy · Monaco · SpainChecked before handoverVessel details kept confidential
At a glance

The job in four lines

Site

Centro Diagnostico Castellano, a healthcare facility in Castelfranco Veneto (Treviso, Italy).

When

20 to 22 January 2021.

Units

Fan coils and split units in the rooms of the centre.

Delivered

Sanitization certificate and a before and after photo report for each unit type.

What we found

What was hiding behind the panels

Once the units were opened, the inside told a different story from the clean grilles seen from the room.

This project was carried out ashore by AirBio, the company AirBio Marine belongs to. The same technicians, equipment, sanitizing method and end-of-job report are used on board yachts and superyachts.

  • Fan coil panels with dark stains, halos and widespread encrustation on the inner side.
  • Visible deposits in the condensate trays, where water stands and biofilm grows.
  • Split unit coils with a compact layer of dust between the fins and dark stains below.
  • Dust on fans, fins and the inner walls of the casings.
Fan coil panel with dark mould stains before AirBio sanitization
Split unit coil with compacted dust between the fins before cleaning
What we did

Every unit opened, cleaned and sanitized

Panels, casings, filters and grilles were removed from every unit. The team cleaned the panels, filters, coils, condensate trays and outlets, then applied a virucidal, bactericidal and fungicidal sanitizer, as stated in the certificate issued to the centre.

Each unit was reassembled and photographed. The centre received a certificate with the dates and the work done, and a photo report showing each type of unit before and after.

Swabs before and after were offered as an option for clients who want a measured result, as in our medical centre case.

Result

Before and after, unit by unit

The photo report shows the same panels, casings and coils after the work: stains and encrustation removed, condensate trays clean, fins free of dust.

For a healthcare facility this matters because fan coils move room air continuously. A dirty condensate tray or a mouldy panel sends what grows there straight back into the room.

This case has no laboratory values: the result is documented with photos and the sanitization certificate.

The same fan coil panel after AirBio cleaning and sanitization
AirBio units on the quay next to a motor yacht
How this applies on a yacht

Yacht cabins have the same weak points

  • Cabin fan coils on yachts run in warm, humid air, so condensate trays fill with slime faster than ashore.
  • A musty smell in a cabin usually starts in the tray or on the coil, not in the duct.
  • We open every unit, clean coil, tray, fan and casing, sanitize and photograph each one for the captain.
  • Guests notice clean air in a cabin before anything else on board.

Yacht fan coil cleaning · Why drain trays get slimy

FAQ

Questions about this case

Was this job done on a yacht?

No. It was carried out ashore by AirBio at a diagnostic centre. We publish it because the units, the method, the team and the report are the same ones we use in yacht cabins.

Why were there deposits in the condensate trays?

Trays collect the water that condenses on the coil. If it does not drain fully, it stands, and bacteria and moulds form a slimy layer.

Do you clean the coils without removing the units?

Yes. The units stay in place: panels, casings and filters are removed so the coil, tray and fan can be reached and cleaned.

Can the result be measured?

Yes. Surface swabs before and after can be added on request and written into the final report.

Sources

Where this information comes from

All information on this page comes from the original AirBio case study, published on airbio.it.

AirBio case study (Italian)

Sanificazione dei ventilconvettori al Centro Diagnostico Castellano

Description of the job and the full before and after photo set.

Method

How AirBio Marine works on board

Survey, treatment, verification and written report.

Onboard survey

Water and air in the same stop?

Tell us the yacht, what the crew has noticed and where she is now: a technician calls you back within 24 hours and plans both sides around your programme.

Onboard survey request

Tell us about the yacht

Yacht length, marina, systems and what you have noticed on board. A technician reads the message and calls you back to plan the survey.

"*" indicates required fields

Name*

Prefer to talk?

+39 0584 433 198

Monday to Friday. For captains, engineers and managers.

Where we work

Italian Riviera and Tuscany marinas and yards — Viareggio, La Spezia, Portofino, Genoa, Sanremo, Livorno, Argentario — and other Mediterranean ports on request.

Documented work

Every job ends with a technical report and photos for the yacht's records.