Metal air duct
Air & HVAC

Yacht Duct Cleaning: HVAC & Ventilation Cleaning and Sanitizing

We open, clean and sanitize the air ducts, supply vents and return grilles, so the air is clean where it leaves the unit, not only at the vent.

Yacht duct cleaning and ventilation cleaning by AirBio Marine. We inspect, mechanically clean and sanitize the HVAC air ducts, supply vents and return grilles that feed your yacht's cabins and saloons. The work is planned with the captain and chief engineer, carried out with interiors protected, and documented with photos in a technical report.

Watch: what collects inside an air distribution system, and why cleaning the grille does not reach it.
Italy · Monaco · SpainAt-berth serviceTechnical reportsDiscreet & professionalA healthier
yacht experience

Yacht duct cleaning at a glance

Yacht duct cleaning means opening the HVAC air ducts, removing the dust and deposits inside them, then sanitizing ducts, supply vents and return grilles so the air is clean where it leaves the system.

What we clean
Air ducts, supply vents, return grilles and the parts of the circuit the crew cannot reach in routine maintenance.
Who it is for
Captains, chief engineers and yacht managers, when the vents look clean but dust keeps returning or the air does not smell fresh.
How it works
A camera inspection first, then protection of the interiors, access to the system, mechanical cleaning, cleaning of vents and grilles, and sanitization.
Cleaning or sanitizing?
Cleaning is the mechanical removal of dust and deposits, by brushing and vacuum extraction. Sanitizing then treats the cleaned surfaces against microbes. We do both, in that order.
How long it takes
From less than a day to a day or more, depending on the size of the yacht and the type of work. We confirm the timing after the survey.
How often
We recommend repeating it at least every six months.
Crew and guests
They can stay on board during the work. It is better to go back into the treated spaces once the treatment has finished. Spaces treated with ozone must be empty while the treatment runs.
Cost
We can give you a rough quote before the survey. The precise quote follows the onboard survey, once we have seen the yacht and the areas to treat.
Where
On board, at berth, in Italy, Monaco and Spain. The work is done by AirBio Marine's own technicians.
What you receive
A written report listing the ducts, vents and grilles treated and the methods used, with inspection camera photos before and after.
How to start
Tell us the yacht, what the crew has noticed and where she is now. A technician calls you back within 24 hours and plans an onboard survey around your programme.
Does this sound familiar?

When the air in the cabins does not feel fresh

Most HVAC problems on board are noticed by guests and crew long before anyone opens a duct. These are the situations that usually lead to a call.

Stale air in closed cabins

Cabins that stay closed between trips may smell stale when the air conditioning restarts. This can be associated with dust and moisture held inside the ducts.

Musty smell after lay-up

After a winter or a long period in the yard, the first days of airflow may carry a damp or musty note. The system should be inspected before guests arrive.

Dust around vents and grilles

Grey marks on the headliner around supply vents may indicate that fine dust is being carried through the ductwork and released into the cabin.

Air that feels heavy

Crew sometimes describe the air as heavy or stuffy even when the temperature is correct. Reduced perceived air quality should be investigated at the source, not only at the outlet.

Condensation near outlets

Droplets or damp patches near diffusers can point to moisture problems inside the duct or at the unit that feeds it.

Inside the ductwork

Why clean-looking vents do not mean a clean system

Ventilation ductwork
Ventilation ductwork

A supply vent can be wiped spotless in a minute, but the duct behind it may run for several metres behind panels and ceilings. Dust, fibres from soft furnishings and fine debris settle along those runs, especially at bends, joints and the first metre after each unit.

Where there is moisture — from condensate, high humidity or cold surfaces — that dust can hold water. It then becomes a place where microbial contamination (bacteria and mould growing on the dust layer) can develop. After a long lay-up, the system may start again with everything that settled while it was idle.

Most yacht systems also recirculate part of the cabin air through return grilles. Contaminants that reach the return side can be carried back into the same cabins again and again. This is why we treat the ductwork as a whole circuit, not as a set of separate vents.

01
RETURN GRILLE

Cabin air, dust and fibres are drawn back into the system.

02
UNIT

Air passes the filter and coil, where moisture condenses.

03
SUPPLY DUCT

Long runs behind panels where dust settles at bends and joints.

04
DIFFUSER

Supply vent where residue may show as grey marks.

05
CABIN

Air reaches guests and crew, then returns to the grille.

Watch

What builds up inside an air distribution system

Ductwork collects dust, fibres and moisture. Over a season this becomes a layer that the airflow passes through every time the system runs, and that the crew and guests breathe in every cabin served by that circuit.

The video shows how the deposit forms and why surface cleaning at the grille does not reach it. The same applies to a yacht HVAC circuit, where runs are shorter but access is far more restricted.

Yacht deck overlooking a turquoise sea
Yacht deck overlooking a turquoise sea
Warning signs

Signs your yacht's ducts should be inspected

None of these signs proves contamination on its own. Together, or when they keep coming back, they are a good reason to look inside the system.

Dust lines on the headliner

Dark streaks around diffusers may indicate dust carried through the supply duct.

Musty or stale cabin air

A smell that appears when the fans start can be associated with contaminated ductwork.

Persistent dampness

High humidity in cabins may mean moisture is lingering in ducts or at the unit.

Condensate problems

Overflowing trays or wet insulation near units can feed growth inside the ducts.

Long lay-up or refit

Systems idle for months, or exposed to refit dust, should be checked before use.

Weak airflow at outlets

Reduced airflow may point to obstructions, dirty grilles or debris in the ducts.

Linda Abenaim, Biologist at Ekonore / AirBioBiologist
The science behind it

Linda Abenaim, Biologist at Ekonore / AirBio

Dust in a duct is not just dust: it holds moisture, skin flakes and spores, and in a warm, humid boat it becomes food for microbes. We inspect with a camera first, so the crew sees what is inside before and after the work.

Linda Abenaim · Biologist, Ekonore / AirBio

Dark marks around the grilles, or dust falling when the AC starts, are signs that the ducts need an inspection.

  • Camerainspection before any work
  • Cleaningmechanical first, then disinfection
  • Proofbefore and after images
Linda Abenaim on LinkedIn
Onboard survey

Not sure what your systems actually need?

Tell us the yacht, what the crew has noticed and where she is now: a technician calls you back within 24 hours and plans the survey around your programme.

Technician checking an air conditioning unit
Technical inspection

How we inspect the HVAC system before cleaning

We start with a walk-through of the system with the chief engineer, using the yacht's drawings where available. The aim is to understand which units feed which cabins, where the ducts are accessible and which areas matter most to the crew.

Where ducts can be reached through vents, grilles or access panels, we use an inspection camera to see the inside surfaces. The photos from this step show the condition of the ducts before any work and are included in the final report.

  • Condition of supply vents, diffusers and return grilles
  • Camera inspection inside ducts where access allows
  • Dust and residue at bends, joints and near the units
  • Signs of moisture, condensate or wet insulation
  • Condition of filters and the unit side of each duct run
  • Areas where cabin air recirculates through the return side
  • Photos of each inspected point for the report
AirBio Marine method

How we clean and sanitize yacht air ducts

Each job follows the same sequence, adapted to the yacht's layout and to what the crew needs to keep running while we work.

Planning and protection

We agree the areas and timing with the captain and chief engineer. Floors, furniture and finishes near the work points are covered and masked.

Access to the system

Vents, diffusers and return grilles are removed where possible, and agreed access panels are opened to reach the duct runs.

Mechanical cleaning

Ducts are brushed to loosen deposits, while vacuum extraction removes the loosened dust so it is not pushed into the cabins.

Vents and grilles

Removed vents and grilles are cleaned separately and refitted, so the visible parts match the condition of the ducts behind them.

Sanitization

The cleaned system and the closed spaces it serves are sanitized, including ozone treatment with our AM-20 mobile generator where suitable, with spaces kept empty.

Checks and report

We re-inspect the treated points, photograph them and deliver a technical report with areas treated, methods used and recommendations.

Francesco Colombo, CEO of AirBio Marine (Ekonore S.r.l.)
A word from our CEO

A duct cleaned without a camera is a duct you have to take on trust. We film before and after, so the result is something the captain can see, not just hear about.

Francesco Colombo

CEO · AirBio Marine, a division of AirBio (Ekonore S.r.l.)

Book an air-system survey
AirBio Marine technician at work on a protected teak aft deck
Real AirBio Marine job: interiors and decks protected before we start
Illustrative example

What the inside of a supply duct can look like

These images are illustrations of typical conditions, not photos of a specific job. Real before and after photos from your yacht are part of our report.

BeforeGrey dust layer inside a yacht supply air duct before cleaning
Supply duct interior with grey dust layer settled along the lower surface.
AfterThe same supply duct with clean metal surface after brushing and vacuum extraction
Same duct after brushing and vacuum extraction, metal surface visible again.

Illustrative visual showing the type of condition we find and the result we work towards. Photos of real AirBio Marine jobs are shown in the gallery below and in every client report.

Real AirBio Marine jobs

Our equipment and work on board

Photos from real AirBio Marine jobs: our units on the quay next to the yacht, the technician kit and the components we open and clean.

References

Where this comes from

These are the public references behind the way we assess and clean an air system on board. One is health guidance for vessels, the other is the trade standard the industry works to. Neither is a legal requirement for a private yacht.

Guideline

WHO — Guide to Ship Sanitation, 3rd edition (2011)

The World Health Organization reference for water, air and food hygiene on board vessels. It is guidance, not law, and it is what most port health authorities work from.

Industry best practice

ACR, the NADCA Standard for Assessment, Cleaning and Restoration of HVAC Systems

The reference most widely used for how an air handling system should be assessed, cleaned and checked. It is a trade standard, not a legal requirement.

What our clients say

Verified reviews on Trustpilot

Reviews of La BioDisinfestazione | Ekonore Italia, the group AirBio Marine belongs to.

Documentation

What you receive

Technical report

A written report listing the ducts, vents and grilles treated and the methods used.

Before and after photos

Photos from the inspection camera and of each treated point, so you can see the difference.

System map of treated areas

Which units and cabins were covered, useful for the next survey or refit.

Points needing attention

Issues found along the way, such as wet insulation or blocked access, flagged for the engineer.

Maintenance recommendations

Suggested intervals and a maintenance plan based on how the yacht is used.

One report for the yacht's technical history

Every job closes with a written report: what was inspected, what was found, what was treated, photos before and after, readings where taken and recommendations for the next check. Useful for the captain, the management company, the next survey and the next season.

On board

Who this service is for

Captain

When guests or crew report stale air, or before the season, you get a clear picture of the ductwork and a documented clean without disrupting the programme.

Chief engineer

You get camera evidence of the duct condition and a record of what was cleaned, which supports your planned maintenance and future access decisions.

Yacht manager

A technical report with photos gives you documentation for the owner, the management company and applicable requirements.

Owner

You know the air in the cabins has been dealt with inside the system, not only at the vents you can see.

Your yacht moves.

Where we clean yacht HVAC systems

We work in marinas and yards along the Italian Riviera and Tuscany, and in other Mediterranean ports on request.

Yacht air duct cleaning is available in these ports. Open your port for local details:

Italy
Monaco
Spain
and beyond

Wherever you are in the Mediterranean, we can be there.

Onboard survey

Book the survey before your next movement

We work in the main Mediterranean marinas and refit yards, with documented results and lab analysis where required.

FAQ

Yacht duct cleaning and ventilation cleaning: questions

Why clean the ducts if the vents already look clean?

Vents are the only part of the system you can see. Dust, fibres and moisture usually collect further in, at bends, joints and near the units, where they cannot be wiped. If those deposits stay, air passing over them can carry particles and smells into the cabins. Cleaning the inside of the ducts deals with the part of the circuit that the crew cannot reach during normal housekeeping.

Can you see inside the ducts before cleaning?

Yes, where access allows. We use an inspection camera through vents, grilles and access panels to see the inside surfaces of the ducts. Not every run on a yacht is reachable, and we say so clearly in the report. The camera images help decide where to focus cleaning and give you a before record to compare with the photos taken after the work.

What is the difference between cleaning and sanitizing ducts?

Cleaning is the mechanical removal of dust and deposits, by brushing and vacuum extraction. Sanitizing is a treatment that reduces microbial contamination on surfaces and in the air, which we carry out after cleaning, including ozone treatment of closed spaces where suitable. Sanitizing a dirty duct is less effective, because the dust layer protects what grows on it, so cleaning always comes first.

When is the best time to clean a yacht's HVAC system?

The most practical moments are during lay-up, at the yard, after a refit that produced dust, or before the season starts. Work can also be planned between charters when the programme allows. We agree the timing with the captain and chief engineer so that cabins can be closed off and protected while we work in each area.

Do you use ozone inside the cabins?

Ozone is used only as a sanitization step for closed spaces, after mechanical cleaning, and only where it suits the area. The space must be empty of people, pets and plants during treatment, and it is ventilated before anyone goes back in. We agree which spaces are treated with the crew and record it in the report.

Will the work damage the interior?

Floors, furniture and finishes near each work point are protected and masked before we start. Vents and grilles are removed carefully and refitted after cleaning. Access panels are opened only where agreed with the chief engineer. If an area cannot be reached without risk to the joinery, we note it in the report rather than force access.

What is yacht duct cleaning?

Yacht duct cleaning is the inspection and mechanical cleaning of the air ducts that carry conditioned air through the vessel, followed by sanitizing where needed. It covers the ducts, supply vents and return grilles, not only the parts you can see from the cabin.

What does yacht ventilation cleaning include?

Yacht ventilation cleaning includes the ducts, the supply and return grilles and the areas around them. We inspect first, clean mechanically, then sanitize, and finish with a technical report with photos. Fan coil units are a separate job, see fan coil cleaning.

Do you offer HVAC duct cleaning and sanitizing for superyachts?

Yes. We plan the work with the captain and chief engineer, protect the interiors, and document what we find. The scope depends on the vessel, so we start with an onboard survey.

How do I know the ducts need cleaning?

Common signs are dust around grilles, a smell when the air comes on, and staining near vents. The only sure way is to open access points and look. Our guide to dirty yacht HVAC lists the signs.

How long does yacht duct cleaning take?

It depends on the size of the yacht and the type of work: from less than a day to a day or more. We confirm the timing after the onboard survey and plan it around the yacht's programme.

How often should yacht duct cleaning be done?

We recommend repeating it at least every six months.

Can the crew and guests stay on board during yacht duct cleaning?

Yes, they can stay on board. It is better to go back into the treated spaces once the treatment has finished. Spaces treated with ozone must be empty of people while the treatment runs.

How much does yacht duct cleaning cost?

We can give you a rough quote before the survey, based on the yacht and what the crew has noticed. The precise quote follows the onboard survey, once we have seen the yacht and the areas to treat.

Onboard survey request

Tell us about the yacht

Yacht length, marina, systems and what you have noticed on board. A technician reads the message and calls you back to plan the survey.

"*" indicates required fields

Name*

Prefer to talk?

+39 0584 433 198

Monday to Friday. For captains, engineers and managers.

Where we work

Italian Riviera and Tuscany marinas and yards — Viareggio, La Spezia, Portofino, Genoa, Sanremo, Livorno, Argentario — and other Mediterranean ports on request.

Documented work

Every job ends with a technical report and photos for the yacht's records.

Motor yacht at sea
Onboard survey

Not sure where the problem starts?
Let the technical team assess it onboard.

In marina, at the yard or during lay-up. We tell you what needs treating — and what doesn’t.

+39 0584 433 198
Discretion.
Expertise.
Peace of mind.